The maximum permissible span of asbestos cement sheets is

The maximum permitted loss of head in a rapid sand filter, is

The maximum pressure to which a pipe is subjected to during its operation, is known

The maximum pressure to which cast iron pipes may be subjected to, is

The maximum pressure which a soil can carry without shear failure, is called

The maximum pressure which the pipe can withstand without any leakage during hydrostatic pressure test, is called

The maximum pull in a cable, carrying a uniformly distributed load and supported at two ends which are at the same level, is at

The maximum quantity of calcium chloride used as an accelerator in cement in percentage by
weight of cement is

The maximum radial distance of a Lemniscate curve, having maximum polar angle a, is

The maximum ratio of span to depth of a cantilever slab, is

The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is

The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is

The maximum rimpull in the first gear of a tractor while towing a load is 6300 kg. The tractor weighs 12.5 tonnes and is operating along a 2 percent upgrade and the rolling resistance is 45 kg/tonne. Pull available for towing the load is

The maximum safe speed on roads, depends on the

The maximum shear stress (q) in concrete of a reinforced cement concrete beam is

The maximum shear stress (qmax) in a rectangular beam is

The maximum shear stress occurs on the filament which makes an angle with the horizontal plane equal to

The maximum slenderness ratio of a compression member carrying both dead and superimposed load is

The maximum slenderness ratio of a steel column, the design of which is governed by wind or seismic forces is

The maximum spacing of contraction joints in rigid pavements is

The maximum spacing of manholes specified by Indian standard in sewers upto 0.3 m diameter is

The maximum spacing of vertical stiffeners is
Where d is the distance between flange angles

The maximum sun’s radiation occurs around:

The maximum tensile and compressive bending stress in extreme fibres of rolled I-sections and channels on the effective section, is

The maximum thickness of concrete floor of a cement warehouse, is

The maximum thickness of expansion joint in rigid pavements is

The maximum total settlement for isolated foundations on clayey soils should be limited to

The maximum total settlement for raft foundation on clayey soils should be limited to

The maximum value of effective stress in the past divided by the present value is defined as over consolidation ratio (OCR). The O.C.R. of an over consolidated clay is

The maximum value of hoop compression in a dome is given by Where, w = load per unit area of surface of dome R = radius of curvature d = thickness of dome

The maximum value of the angle of turning of the nose gear large jet aircrafts, is limited to

The maximum value of the horizontal range for a projectile projected with a velocity of 98 m/sec is

The maximum velocity of a body vibrating with a simple harmonic motion of amplitude 150 mm and frequency 2 vibrations/sec, is

The maximum water content at which a reduction in water content does not cause a decrease in volume of a soil mass, is known

The means of access for inspection and cleaning of sewer line is known as

The measure to remove water logging of land, is

The measurement is made for stone work in square metre in case of

The measurement is made in square metre in case of

The meatcentric height is the distance between the

The mechanical advantage of an ideal machine is 100. For moving the local through 2 m, the effort moves through

The mechanism method and the statical method give

The mechanism method of plastic analysis satisfies

The melting point of silica is:

The member forces in a statically in determinate truss

The member which is placed horizontally to support common rafter of a sloping roof, is

The members which support covering material of a sloping roof, are

The mercury does not wet the glass. This is due to the property of the liquid known as

The meridian of a place is

The Metacentric heights of two floating bodies A and B are 1 m and 1.5 m respectively. Select the correct statement.

The meteorological condition which influences the size and location of an air port is

The method generally preferred to for contouring an undulating area, is

The method of addition polymerization is used for obtaining:

The method of analysis of distribution system in which the domestic supply is neglected and fire demand is considered is

The method of design of flexible pavement as recommended by IRC is

The method of design of steel framework for greatest rigidity and economy in weight, is known as

The method of finding out the difference in elevation between two points for eliminating the effect of curvature and refraction, is

The method of moving each brick through a small horizontal distance before it is finally laid in any brick wall and pressing it by means of brick hammer, is known as

The method of reversal

The method of surveying by triangulation was first introduced by the Dutchman Snell in

The method of the slices is applicable to

The methods used for locating the plane table stations are
(i)      Radiation
(ii)      Traversing
(iii)     Intersection
(iv)      Resection
The correct answer is

The minimum and maximum diameters of sewers shall preferably be

The minimum centre to centre distance of friction piles of 1 m diameter, is

The minimum clear cover for R.C.C. columns shall be

The minimum compressive strength of 1st class bricks should be

The minimum compressive strength of 2nd class bricks should be

The minimum cover in a slab should neither be less than the diameter of bar nor less than

The minimum cover to the ties or spirals should not be less than

The minimum cross fall of shoulders is kept

The minimum cube strength of concrete used for a pre-stressed member, is

The minimum depth of building foundations on

The minimum depth of foundation in clayey soils is

The minimum design speed for hairpin bends in hill roads is taken as

The minimum design speed of various types of highways in plain terrain is the same as the ruling design speed of

The minimum diameter of a sewer is kept

The minimum diameter of longitudinal bars in a column is

The minimum diameter of sewer to be adopted is

The minimum diameter of turning besin, where ships turn by going ahead and without tug assistance should be Where ‘L’ is the length of the largest ship to use the port

The minimum dissolved oxygen which should always be present in water in order to save the aquatic life is

The minimum distance between the centres of bulb of diameter du, of a multi under reamed piles, is

The minimum edge distance of a rivet line connecting two or more plates, is kept equal to 37 mm plus (where t is the thickness in mm of the thinner outside plate).

The minimum head room over a stair must be

The minimum number of main steel bars provided in R.C.C.

The minimum number of rivets for the connection of a gusset plate, is

The minimum percentage of chemical ingredient of cement is that of

The minimum percentage of silica, alumina and ferric oxide in lime for white washing, is

The minimum pitch of rivet holes of diameter d should not be less than

The minimum range for sliding the focusing lens in the internal focusing telescope for focusing at all distances beyond 4 m is

The minimum ratio of the radii of two circular curves of a compound curve, is kept

The minimum recommended diameter of sewers, is

The minimum road width is taken

The minimum strength of the mortar used in load bearing brick masonry, is

The minimum super-elevation in rolling terrain in plains, is limited to

The minimum thickness of a flat slab is taken

The minimum thickness of a steel plate, which is directly exposed to weather and is not accessible for cleaning and repainting, should be:

The minimum thickness of plates in a steel stack should be

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice
the diameter of the bar subject to a minimum of

The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is

The minimum value of camber provided for thin bituminous surface hill roads, is

The minimum vertical clearance of overhanging cliffs or any other structure above the surface of a hill road, should be

The portion of the brick cut across its width and having its length equal to that of a full brick, is
known as