All syllabus Civil Engineering Mock test - 7 (Important 50 Questions) - ENGINEERING BIX

All syllabus Civil Engineering Mock test – 7 (Important 50 Questions)



Welcome to your All syllabus Civil Engineering Mock test - 7
Take an exciting test in All syllabus Civil Engineering

(Building Materials, Concrete Technology, Strength of Materials, Soil Mechanics and Foundation Engineering, RCC design, Surveying, Highway, Hydraulics, Water Supply, Waste water, Steel, Irrigation,  Estimation, Hydrology and Railway ) 

You have only 1 hour  to complete the test (50 Important Questions)
Wish you all the best!!!
Name
Email
A pile is embedded quite deep is a clay stratum. The clay has a cohesion of 3.5t/m2. The ultimate point resistance of the pile will be:
A unit working purely on anaerobiosis is:
The ratio of ultimate creep strain to elastic strain is known as:
The units of viscosity are:
The settlement of coarse aggregate towards bottom with scum rising towards the surface is known as:
A row of rivets parallel to the direction of force is called:
Setting of Laminscate transition curve is done with:
The ratio of the total elongation of a bar of uniform circular cross-section produced under its own weight to the elongation produced by an external load equal to the weight of the bar is:
The weight of a rail and its section is decided on the basis of:
Concentration of fluorides desirable in water is:
On wetting, cohesive soils:
Mostly used coagulant in treatment of water is:
The allowable stress to which a structural member can be subjected, is called:
Chromatic aberration in a telescope is reduced by using:
The minium ratio of thickness of elements in compression, in terms of their outstanding length has been specified to prevent:
To determine the whole volume formed by given sections over a given length, the prismoidal formula can be applied:
Moment Distribution method of Structural analysis is applicable to:
In the design of purlins, depth of angle section should not be less than:
A vertical member of frame, which is employed to subdivide a window or door vertically is:
The piles which do not support the load by them selves, but act as a medium to transmit the load from the foundation to the resisting sub-stratum are known as:
A structural member subjected to compressive force in a direction parallel to its longitudinal axis is called:
The effective depth of T-beam is the distance between the:
A contour line:
A CPM network is to be drawn considering:
The rise and fall method of reduction of levels provides a check on:
Which of the followings is measured in a CBR test on soils:
Which of the following instruments is used for spot speed measurement of a vehicle?
The process of mixing some mortar in the mixer at the beginning of the first batch concrete mixing is called:
The forces which meet at one point, but their line of action do not lie in a plane, are called:
The most economical section of a trapezoidal channel is one which has hydrulic mean depth equal to:
In which of the following, kerosene oil is used for its preparation?
The water content in the soil is:
Match List I with II and select correct answer from the codes given below the Lists:
List I                                    List II
A. Abrasion test                 1. Durability
B. Crushing strength test  2. Toughness
C. Impact Test                    3. Hardness
D. Soundness Test             4. Compressive strength
Codes:
A line joining some fixed stations on main survey lines is:
Bearings are provided in bridges, in order to:
1. Distribute the load from susperstructure on a large areas and to transfer to piers
2. Allow the grid order of the bridge to taken a free angular movement at the ends when loaded
3. Allow free movement of girders due to temperature variations.
4. Prevent excessive damage to the bridge if any pier sink slightly
Of these the correct utilities are
The ratio of the total elongation of a bar of uniform cross-section produced under its own weight to the elongation produced by an external load equal to the weight of the bar is: 
In a restrained rectangular slab subjected to a uniformly distributed load, the yield lines form first:
The height of instrument (HI) is equal to:
A short column 300 mm x 300 mm is reinforced with 4 bars of 20mm dia. (Fe–415 grade). If concrete is M-20 grade, the max. axial load Pu (kN) allowed on it is:
Match List I with List II and select the correct answer using the codes Given below the lists:
List I                                      List II
A. Plain sedimentation test       1. Hydraulic loading ruse
B. Fon- exchange                      2. Exhaust of bed
C. Flocculator                            3. Settling velocity
D. Rapid sand filter                   4. Velocity gradient
Codes:
The first stage of natural process of sludge digestion is:
The modulus of elasticity (E) of concrete is given by: 
In a CBR test, If the CBR value at 5 mm is greater than that at 2.5 mm:
The outer axis of a theodolite is:
Hydraulic radius is equal to:
A flow in which the quantity of liquid flowing per second is constant, is called:
The main object of providing a camber is:
A given material has young’s modulus E, modulus of rigidity G and passion’s ratio 0.25. The ratio of young’s modulus to modulus of rigidity of this material is:
In a Tee-Beam the breadth of the rib is equal to the:
Match List I with List II and select the correct answer using the codes given below the:
(Organism)                      (Disease Transmitted)
A. Bacteria                       1. Infection hepapatities
B. Viruses                         2. Amoebic dysentery
C. Protozoa                      3. Paratyphoid
D. Helminths                    4.Gunica – worm infections
Codes:






Share to all